-
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
-
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
-
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
3D printed wing retainer clip. I created this after the original fitting (3mm T-nut) ripped out of the ply twice.
-
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
-
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
-
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
-
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
-
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
-
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
-
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
1200mm wingspan Piper J3 Cub.
-
Piper J3 Cub, fuselage covered with film (but not shrunk yet).
Piper J3 Cub, fuselage covered with film (but not shrunk yet).
Piper J3 Cub, fuselage covered with film (but not shrunk yet).
-
Wing covered
Wing covered
Wing covered
-
Just motor and covering required now.
Just motor and covering required now.
Just motor and covering required now.
-
Just motor and covering required now.
Just motor and covering required now.
Just motor and covering required now.
-
Just motor and covering required now.
Just motor and covering required now.
Just motor and covering required now.
-
Just motor and covering required now.
Just motor and covering required now.
Just motor and covering required now.
-
Just motor and covering required now.
Just motor and covering required now.
Just motor and covering required now.
-
Fuselage with tail attached.
Fuselage with tail attached.
Fuselage with tail attached.
-
Fuselage with tail attached.
Fuselage with tail attached.
Fuselage with tail attached.
-
Port wing - attaching lower skin.
Port wing - attaching lower skin.
Port wing - attaching lower skin.
-
Horizontal & vertical stabalisers covered.
Horizontal & vertical stabalisers covered.
Horizontal & vertical stabalisers covered.
-
Horizontal & Vertical stabalisers. The Rudder & Elevator are hinged with Blenderm tape.
Horizontal & Vertical stabalisers. The Rudder & Elevator are hinged with Blenderm tape.
Horizontal & Vertical stabalisers. The Rudder & Elevator are hinged with Blenderm tape.
-
Starboard wing with sheeting glued in place.
Starboard wing with sheeting glued in place.
Starboard wing with sheeting glued in place.
-
Starboard wing with aileron cut off from the main wing.
Starboard wing with aileron cut off from the main wing.
Starboard wing with aileron cut off from the main wing.
-
Starboard wing with sheeting glued in place.
Starboard wing with sheeting glued in place.
Starboard wing with sheeting glued in place.
-
Wing rib types. Identifiers are to match with online instructions.
Wing rib types. Identifiers are to match with online instructions.
Wing rib types. Identifiers are to match with online instructions.
-
Starting to build the starboard wing. component identifiers are to match in with the online instructions.
Starting to build the starboard wing. component identifiers are to match in with the online instructions.
Starting to build the starboard wing. component identifiers are to match in with the online instructions.
-
Started building the fuselage.
Started building the fuselage.
Started building the fuselage.
-
All the parts laid out ready for assembly.
All the parts laid out ready for assembly.
All the parts laid out ready for assembly.
-
Box label.
Box label.
Box label.
-
1200mm wingspan Piper J3 Cub kit.
1200mm wingspan Piper J3 Cub kit.
1200mm wingspan Piper J3 Cub kit.